An instrument used to test the abrasion resistance of a material.
All utensils and decorative articles used on the table for meal service. (ASTM C 242).
Someone who can read blueprints and is familiar with the specifications. This person makes tracings of special details concerning the tilework after gathering the necessary information and then estimates the labor, materials, tile quantities, and special trim shapes needed to complete the job.
An inspection technique whereby a coin, key, or other small metallic object is tapped against an installed tile to determine by sound whether the tile is completely bonded to its hacking. Tilesetters often tap the tile with a pointing trowel to determine that a good bond has been achieved. (TCA)
The pulling force necessary to break a given specimen divided by the cross sectional area. Units given in lbs./in2 (P.S.I.). It measures the resistance of a material to stretching without rupture. Normally is not used with reference to elastic materials which recover after elongation.
Hard baked clayware, including tile, of variable color, averaging reddish red-yellow in hue and of high saturation. (CTI)
A porous, red clay ware characterized by embossed decorations of the same color and a satin-like unglazed surface. Originated on the Island of Samos. (ASTM C 242).
See Concrete, terrazzo.
A terrazzo surface, on a portlandl cement and sand body, made by a mixture of marble chips and portland cement and usually ground smooth. (CTI)
A small chip of glass or marble used in mosaic formations. (CTI)
A trial, examination, observation, or evaluation used as a means of measuring a physical or chemical characteristics of a material, or a physical characteristic of a structural element or a structure.
A device for applying test conditions and accurately measuring results.
The act of determining whether ceramic tile are acceptable. See Physical properties of ceramic tile.
Ability of a material to conduct heat; physical constant for quantity of heat that passes through unit volume of a substance in unit of time when difference in temperature of two opposite faces is one degree.
A term used to describe the bonding of tile with suitable materials applied approximately 1/8"' thick. See also Dry-Set mortar.
The 18-gauge galvanized wire used in construction work.
A ceramic surfacing unit, usually relatively thin in relation to facial area, made from clay or a mixture of clay and other ceramic materials, called the body of the tile, having either a glazed or unglazed face and fired above red heat in the course of manufacture to a temperature sufficiently high to produce specific physical properties and characteristics. (ASTM C 242).
See definition for Mounted tile.
The the cutter is one of the most efficient and economical tools in the tilesetting trade. A popular model is the hand-drawn tile cutting board that is adjustable.
Tile assembled into units or sheets and bonded together to facilitate handling. (TCA) Back-mounted tile. Mounted tile with perforated paper, fiber mesh, or other suitable bonding material applied to the backs or edges of the tile so that a relatively large proportion of tile area iS exposed to the setting bed. Face-mounted tile. Mounted tile with paper applied to the faces of the tile. The water-soluble adhesive can be removed easily prior to grouting of the joints.
In finely ground form used in glazes as an opacifier.
A vitreous ceramic whiteware for technical application in which titania (TiO,) is the essential crystalline phase. (ASTM C 242).
Any ceramic whiteware in which titania (TiO,) is the essential crystalline phase. (ASTM C 242).
A type of lumber or precast concrete pile having mated projecting and grooved edges to provide a tight fit, abbreviated "T & G."
A trammel bar, which is easy to construct, is more accurate than many other layout tools. It is used to erect perpendicular lines and to bisect angles. The tilesetter can make a trammel bar from a stick of a size that is suitable for the particular job.
A batch of concrete prepared to establish or check proportions of the constituents.
Units of various shapes consisting of such items as bases, caps, corners, mouldings, angles, etc.,, necessary or desirable to make a complete installation and to achieve sanitary purposes as well as architectural design for all types of tile work. (ASTM C 242).